Mikrotik RouterOSをアップデートした記録 6.43.7→6.43.8
アップデート内容確認
MikrotikのRouterOSを
6.43.7から6.43.8にWinboxを使ってアップデートします
変更点の確認はこちら
MikroTik Routers and Wireless – Software
https://mikrotik.com/download/changelogs
What's new in 6.43.8 (2018-Dec-21 07:10): MAJOR CHANGES IN v6.43.8: ---------------------- !) telnet - do not allow to set "tracefile" parameter; ---------------------- Changes in this release: *) bridge - fixed IPv6 link-local address generation when auto-mac=yes; *) capsman - fixed "group-key-update" parameter not using correct units; *) crs3xx - improved data transmission between 10G and 1G ports; *) console - properly remove system note after configuration reset; *) dhcpv4-server - fixed dynamic lease reuse after expiration; *) dhcpv6-server - properly handle DHCP requests that include prefix hint; *) ethernet - fixed VLAN1 forwarding on RB1100AHx4 and RB4011 devices; *) gps - added "coordinate-format" parameter; *) led - fixed default LED configuration for RBMetalG-52SHPacn; *) led - fixed PWR-LINE AP ethernet led polarity ("/system routerboard upgrade" required); *) lte - disallow setting LTE interface as passthrough target; *) lte - fixed DHCP IP acquire (introduced in v6.43.7); *) lte - fixed passthrough functionality when interface is removed; *) lte - increased reported "rsrq" precision; *) lte - reset USB when non-default slot is used; *) package - use bundled package by default if standalone packages are installed as well; *) resource - fixed "total-memory" reporting on ARM devices; *) snmp - added "tx-ccq" ("mtxrWlStatTxCCQ") and "rx-ccq" ("mtxrWlStatRxCCQ") values; *) switch - fixed MAC learning when disabling interfaces on devices with Atheros8327 and QCA8337 switch chips; *) system - fixed situation when all configuration was not properly loaded on bootup; *) timezone - fixed "Europe/Dublin" time zone; *) upgrade - automatically uninstall standalone package if already installed in bundle; *) webfig - do not show bogus VHT field in wireless interface advanced mode; *) winbox - added "allow-roaming" parameter in "Interface/LTE" menu; *) winbox - allow to change VHT rates when 5ghz-n/ac band is used; *) winbox - renamed "Radius" to "RADIUS"; *) winbox - show "Switch" menu on RB4011iGS+5HacQ2HnD and RB4011iGS+; *) wireless - added new "installation" parameter to specify router's location; *) wireless - improved stability for 802.11ac; *) wireless - improvements in wireless frequency selection;
今回も不具合修正がメインですね
所要時間は5分程度
アップデートの手順
事前にバックアップをした上で以下の操作でアップデートを実行
RouterOSのアップデート
System→PackagesでPackage Listを開いて左上の「Check For Updates」を選択
6.43.7から6.43.8へアップデートと表示出てるのを確認して「Download&Install」を押す
無事に完了すると自動で再起動開始されます
再起動後にPackage ListにてVersionが6.43.8になっているのを確認
FWのアップデート
FW更新を行うためSystem→Routerboardを開く
Upgrade Firmwareが6.43.8になっているのを確認して「Upgrade」ボタンを選択
確認画面を経て更新完了すれば以下メッセージが表示される
”Firmware upgraded successfully. please reboot for changes to take effect!”
指示通りSystem→Rebootから再起動
再起動後にSystem→RouterboardにてCurrent Firmwareが6.43.8になっているのを確認
最後に最新Verの状態でバックアップをして完了
コメント